Відео

How are you able to regulate the current ?

got a 2008 SM here that kept dying, that exact connector turned out to be my problem too. Thanks mate, saved me ££

wow funny we have the same air compressor it was given to me from my dad when he passed and last night went to go turn it on it turned on but it seemed to sputter a little bit like it lost its power for a second but isnt it a great air compressor?

Nice video thanks

Now, while they are paralleled, turn one generator off so that you can simulate one running out of fuel and let us know what happens.

The engine when first woke up in the Sidekick : "Wh... where am i? What happend to my streamline body?... no.. no.. moooooo.."

How do you wire the light socet to the plugs?

Flywheel effect due to Lenz's law of electromagnetics

Thank you. I've been looking online for backup generators and was wondering about 3 vs single phase power.

Very impressed that the waveform is even cleaner than utility power.

In that zigzag configuration it looks like two windings are in series with each other. That would probably increase the source impedance of the generator making that leg more susceptible to Distortion from poor power factor loads.

Great video! But next time please note socket sizes as you use them, would be really helpful.

Hydrogen is not just flammable ,It is highly explosive ! I have personally seen 2 batteries explode and heard of another, one of the explosion caused battery parts to penetrate a wooden ceiling that was 20 feet high !, I am a welder and I would not ever do this, I also have a US patent on safety jumper cables that will not operate unless hooked up correctly

Hey matt i have a isuzu pup with the 2.2 i was wondering if you would make another one of those turbo manifolds for me for some pay love the build ?

No issues with coil-bucket contact? I've read content about how just spacer lifts cause coil-bucket contact due to wheel travel.

The fix worked for me on a 2014 caravan but now both my keys dont wireless unlock or remote start. Anyone else have this prob?

Just got my QRS10 going on a VFD. It cycles from 50hz loaded and 30hz unloaded then set to turn off after ten minutes on idle.

inventors is that to hard to invent a simple, cheap battery bank to be conected to electricity all the time when we are using the battery bank to weld, meanwhile we weld, so we never be out of charge and the welding machine will be in operation all day!

Great tip thanks

Great video. This is why I put dielectric grease on when doing anything electric

How was the ride compared to factory?

Who the hell wants to hear that metal to metal smashing every other second wow what a du.p setup

Yoo... I have ended up with this trailer n have some questions for ya...

Thank you so much! I have a 4’x 8’ Lincoln table and I have a lot of mold growing. I will be cleaning it out like this and I will make the same concoction. The red stuff from Lincoln is terrible and expensive.

As far as electrical goes what was the major differences as I’m about to do this swap next week on a 2003 2.0 tracker Thank you

🤩🤩🤩🤩🤩❤️❤️❤️🎉🎉🎉🙏

Running a duel LED is great. It's a bit more work to move wires around but it's way better.

How did you get around the 400hz to 60hz

what was the total current you were producing mate ?

How did you get around the 400hz to 60hz ?

Yeah but it doesn't work so smoothly with every car that has it ....

You skipped over the part where you wrestle with that one bolt at the top of the bell housing.

Matt.......Thank you VERY much for the video. It is exactly what I needed. Good job.

It's probably designed off of the old M16. Try an M16 bolt carrier group. It's odd that it would be long since the takedown/pivot pin holes lined up.

Gracias, buen video.

How to you wire to get the 208 i dont understand each leg has 120 how do you connect then to get 208 ?

I hate town as well. Great video. General maintenance or spend 100k on a 60k truck.

This is amazing. Short and sweet, and I love the comment that mentions using wire hangers and multiple sunglasses. An emergency welding station with everyday materials! Knowledge truly is priceless. Thank you!

I used a 5/8" spark plug socket to pop the old one out. Took more time to type this than it took to remove the old one.

I had a theory this was a thing, I'm calling this theory confirmed and running wild with it

Does the mep 004a load up like the map 005a when not enough load on them.

I want to know what can you use as a rod for alternative now:)

This video is great, thanks, how/where did you pass the wires through the firewall?

I have seen another video where the guy did not remove the hub from the axle; rather, left the hub attached to the axle removing all as one. Is it better to remove the hub first or does it really matter? Thanks! Great video.

Just changed mine in around 10 mins, thx for teaching me something new that I can do myself 🫡👏

Grest video.

If you have a mil gen 3 phase your going to run single 120 and 208 but not going to run any 3 phase what do you do with the other hot leg?

Awesome, thanks for the recipe! I just completed my own table build yesterday & was wondering what to put in the water. Nice shop!

Just installed on my pickup. Haven't commented on a video, but specifying which wires to tap into and where you ran wiring saved me a headache. Really appreciate it!

Love this setup! I’m on the hunt to try and find this headlight online. If anyone had a current link I would appreciate it! Thavkyou for sharing the design ! Now to track down someone with a 3D printer ! Also on a side note - I have a drz400 as well as a Ducati 😅 - older 2000 monster 900 love the sound!